Replace the Thermocouple on a Whirlpool Water Heater
A bad thermocouple is the most likely culprit when your Whirlpool water heater fails to heat the water in the tank. The pilot light heats the thermocouple, which generates electric current that tells the gas control valve/thermostat to continue to feed gas to the burner assembly. If the pilot light should go out, the thermocouple closes the gas control valve/thermostat by interrupting the electrical current.
Instructions
1. Turn off the gas at the manual shut-off valve that supplies the gas to control valve/thermostat by turning it clockwise. Turn off the gas control valve/thermostat by turning the thermostat to the lowest position, and turning the control knob on top of the valve to the OFF position. (The gas control valve/thermostat is a single part; it controls the flow of the gas through a manifold tube as you adjust the thermostat.)
2. Remove the outer door from the bottom of the water heater by grasping the door with your hands, and pulling the metal tabs attached to the outer door from the slots on the body of the water heater. The outer door covers the manifold door assembly, thermocouple, manifold tube and pilot tube, protecting them from damage.
3. Remove the two screws that secure the manifold door assembly to the tank. Use an adjustable wrench to loosen the thermocouple from beneath the gas control valve/thermostat by turning it counterclockwise. The thermocouple is a thin copper tube attached to the left of the manifold tube. Use the adjustable wrench to loosen the pilot tube by turning it counterclockwise. The pilot tube is a small-diameter tube located to the right of the manifold tube.
4. Loosen the manifold tube from the gas control valve/thermostat by turning it clockwise with the adjustable wrench. The manifold tube is a flexible, corrugated metal tube that attaches to the gas control valve/thermostat between the pilot tube and the thermocouple. It is the largest of the three tubes.
5. Pull the wire from the pilot igniter button connected to the gas control valve/thermostat, and pull the two manifold burner assembly connector wires from the gas control valve/thermostat. Grasp the igniter wire and the two manifold burner assembly connector wires in your hand and pull down on them, pulling them out of the valve. Grasp the manifold tube in your hand and pull down and away from the gas control valve/thermostat, releasing the thermocouple, pilot tube and manifold tube from the valve.
6. Remove the manifold burner assembly from the burner chamber by pulling it out and away from the water heater. Remove the two piece wire connector that secures the thermocouple and igniter wire through the manifold door by removing the retainer clip holding it.
7. Pull the thermocouple from the pilot bracket attached to the manifold burner assembly. Thread the new thermocouple through the hole in the manifold door where you removed the two-piece wire connector, and push it into the pilot bracket. Replace the two-piece wire connector onto the thermocouple and igniter wire, securing it with the retainer clip, and slide the manifold burner assembly back into the water heater.
8. Reattach the manifold tube, pilot tube and thermocouple to the gas control valve/thermostat and tighten them using the adjustable wrench. Replace the igniter wire into the igniter, and push the two manifold burner assembly connector wires into the gas control valve/thermostat.
9. Replace the screws in the manifold door assembly that you removed in Step 2, and replace the outer door. Turn on the gas at the manual shut off by turning the valve counterclockwise, and turn on the gas supply valve/thermostat on the water heater by turning the thermostat to the desired setting and the gas control knob to the ON position.
Related Posts:
Change A Whirlpool Hot Water Heater Anode Rod
Although Whirlpool manufactures a number of different water heater models, both gas and electric, one component that the majority of them have in common is the use of an anode rod. Sometimes calle...
Vent A Hot Water Heater
If you own a gas water heater you may have noticed a galvanized vent pipe coming out of the top and running to your chimney. The pipe is necessary because when your hot water heater burns natural...
Troubleshoot Whirlpool Dishwashers
Troubleshoot Whirlpool DishwashersA dishwasher is an ideal addition to your kitchen appliances. A dishwasher cleans dishes so you don't have to. Dishwashers come in a variety of different brands,...
Bypass The Water Filter On Frigidaire Model Number Frs6lf7fm
Bypass the Water Filter on Frigidaire Model Number FRS6LF7FMThe Frigidaire FRS6LF7FM is a side-by-side refrigerator with a water and ice dispenser in the door. The water runs through a filter insi...
Replace A Thermal Fuse On A Kitchenaid Dishwasher
KitchenAid dishwashers have a thermal fuse, located inside of the control board compartment of the dishwasher. The thermal fuse is designed to cut power to the dishwasher when it detects an abnorm...
